文件列表:

compconv2.m (663, 2005-01-08)
compoversamp2.m (722, 2005-01-08)
crosscorr.m (670, 2005-01-08)
DELAY.M (741, 2005-01-08)
DESPREAD.M (1013, 2005-01-08)
DSCDMA.M (6442, 2005-01-08)
FADE.M (2167, 2005-01-08)
GOLDSEQ.M (650, 2005-01-08)
hrollfcoef.m (1652, 2005-01-08)
JAUTOCORR.M (624, 2005-01-08)
KCOMB2.M (718, 2005-01-08)
MSEQ.M (1241, 2005-01-08)
qpskdemod.m (723, 2005-01-08)
QPSKMOD.M (914, 2005-01-08)
SEFADE.M (1742, 2005-01-08)
SHIFT.M (1270, 2005-01-08)
SPREAD.M (1004, 2005-01-08)

% % README Chapter 5 % % by Hiroshi Harada % % If you have any bugs and questions in our simulation programs, please e-mail % to harada@ieee.org. We try to do our best to answer your questions. % In this directory, we can find the seventeen files. The relationship between file name and the number of program written in the book is shown in as follows. Program5-1 autocorr.m Program5-2 crosscorr.m Program5-3 mseq.m Program5-4 shift.m Program5-5 goldseq.m Program5-6 dscdma.m Program5-7 spread.m Program5-8 despread.m Program5-9 compoversamp2.m Program5-10 compconv2.m Program5-11 comb2.m Program2-5 fade.m Program2-6 sefade.m Program2-7 delay.m Program3-3 hrollfcoef.m Program3-9 qpskmod.m Program3-10 qpskdemod.m If you would like to try to use the above programs by using MATLAB. First of all, please copy all of files to your created adequate directory. Then, you start to run MATLAB and you can see the following command prompt in the command window. >> Next, you can go to the directory that have all of programs in this section by using change directory (cd) command. If you copy all of files to /matlabR12/work/chapter5, you only type the following command. >> cd /matlabR12/work/chapter5 (I) Usage of the functions (1) Calculation of auto-correlation If you would like to calculate of a sequence [1 1 1 -1 -1 1 -1], you can type the following command >> autocorr([1 1 1 -1 -1 1 -1]) As a result, the following auto-correlation value is obtained. ans = 7 -1 -1 -1 -1 -1 -1 (2) Calculation of cross-correlation If you would like to calculate of sequences [1 1 1 -1 -1 1 -1] and [1 -1 1 -1 1 -1 1], you can type the following command. >> crosscorr([1 1 1 -1 -1 1 -1],[1 -1 1 -1 1 -1 1]) As a result, the following cross-correlation value is obtained. ans = -1 3 -1 3 -5 3 -1 (3) Generation of M-sequence The function mseq(X,Y,Z) outputs an M-sequence of the stage number X, the position of feedback taps Y, and the initial value of registers Z. In case of X=3, Y=[1 3], and Z=[1 1 1], >> mseq(3,[1 3],[1 1 1]) ans = 1 1 1 0 1 0 0 And, the function mseq(X,Y,Z,N) outputs N one-chip shifted M-sequences. >> mseq(3,[1 3],[1 1 1],3) ans = 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 (4) Generation of Gold sequence First of all, you must prepare preferred pair of M-sequences. For example, you type the following commands, and generate M-sequences m1, m2. >> m1=mseq(3,[1 3],[1 1 1]) m1 = 1 1 1 0 1 0 0 >> m2=mseq(3,[2 3],[1 1 1]) m2 = 1 1 1 0 0 1 0 Next, you type the following command. >> goldseq(m1,m2) ans = 0 0 0 0 1 1 0 As a result, you can get a Gold-sequence [0 0 0 0 1 1 0]. And, the function goldseq(m1,m2,N) outputs N one-chip shifted Gold-sequences. >> goldseq(m1,m2,3) ans = 0 0 0 0 1 1 0 1 0 0 1 1 0 1 0 1 0 1 0 0 0 (II) Simulation of synchronous DS-CDMA (1) Set paremeters First of all, we set simulation parameters in "dscdma.m". (a) Symbol rate sr = 256000.0; (b) Number of modulation levels ml = 2; (c) Number of symbols nd = 100; (d) Eb/No ebn0 = 3; (e) Number of filter taps irfn = 21; (f) Number of oversample IPOINT = 8; (g) Roll off factor alfs = 0.5; (h) Number of users user = 1; (i) Code sequence (1-M-sequence, 2-Gold sequence, 3-Orthogonal Gold sequecne) seq = 1; (j) Number of stages stage = 3; (k) Position of feedback taps for 1st ptap1 = [1 3]; (l) Position of feedback taps for 2nd ptap2 = [2 3]; (m) Initial value of registers for 1st regi1 = [1 1 1]; (n) Initial value of registers for 2nd regi2 = [1 1 1]; (o) Do you include the Rayleigh fading or not ? (0-No, 1-Yes) rfade = 0; (p) Delay time itau = [0,8]; (q) Attenuation level dlvl1 = [0.0,40.0]; (r) Number of waves to generate fading n0 = [6,7]; (s) Initial phase of delayed wave th1 = [0.0,0.0]; (t) Set fading counter itnd1 = [3001,4004]; (u) Number of direct wave + delayed wave now1 = 2; (v) Doppler frequency [Hz] fd = 160; (w) Flat fading or not (0-Normal, 1-Flat) flat = 1; (x) Simulation number of times nloop = 1000; (y) Output file name to store the simulation results fid = fopen('BER.dat','a'); (2) Type just the following command >> dscdma (3) Then, you can see the following simulation result on your command window. 3 4492 200000 2.246000e-002 where first number 3 is Eb/No, second number 4492 is the number of errors, third number 200000 is the number of data, and fourth number 2.246000e-002 is BER. And, simulation result is stored in the file (BER.dat) defined with (1)-(y). If you change the paramter rfade from 0 to 1, you can include the effect of fading. By changing the value of Eb/N0 (variable ebn0), you can obtain the graph that shows the relationship between Eb/N0 and BER and that can been seen in the figures of the book. ********** end of file **********

近期下载者：

相关文件：

评论：[我要评论] [举报此文件]

收藏者：