文件列表:

RST_IllegalOpcode (0, 2019-04-05)
RST_IllegalOpcode\main.c (4708, 2018-04-27)
RST_IllegalOpcode\stm8s_conf.h (4730, 2018-04-27)
RST_IllegalOpcode\stm8s_it.c (13428, 2018-04-27)
RST_IllegalOpcode\stm8s_it.h (5539, 2018-04-27)

/** @page RST_IllegalOpcode Illegal Opcode Reset @verbatim ******************** (C)COPYRIGHT 2014 STMicroelectronics ******************* * @file RST/RST_IllegalOpcode/readme.txt * @author MCD Application Team * @version V2.0.4 * @date 26-April-2018 * @brief Description of Illegal Opcode reset example ****************************************************************************** * * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); * You may not use this file except in compliance with the License. * You may obtain a copy of the License at: * * http://www.st.com/software_license_agreement_liberty_v2 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ****************************************************************************** @endverbatim @par Example description This example provides a short description of how to generate, detect and manage an illegal opcode reset. Pressing the KEY button will cause a jump to a specific memory address where an illegal opcode is written, so a reset is generated. LEDs from 1 to 4 start blinking fast signaling the ILLOP reset. When the reset flag is cleared they will blink slowly. @par Directory contents - RST\RST_IllegalOpcode\main.c Main file containing the "main" function - RST\RST_IllegalOpcode\stm8s_conf.h Library Configuration file - RST\RST_IllegalOpcode\stm8s_it.c Interrupt routines source - RST\RST_IllegalOpcode\stm8s_it.h Interrupt routines declaration @par Hardware and Software environment - This example runs on STM8S and STM8A High density, Medium density and Low density devices. - This example has been tested with STMicroelectronics STM8/128-EVAL evaluation board and can be easily tailored to any other development board. - STM8/128-EVAL Set-up - LED1..LED4 - Key push button @par How to use it ? In order to make the program work, you must do the following : - Copy all source files from this example folder to the template folder under Project\Template - Open your preferred toolchain - Rebuild all files and load your image into target memory - Run the example - The LD1, LD2, LD3 and LD4 toggle slowly - If you press the button, a Reset occurs and LD1,2,3 and 4 blink fast @note - High-Density STM8A devices are the STM8AF52xx STM8AF6269/8x/Ax, STM8AF51xx, and STM8AF6169/7x/8x/9x/Ax microcontrollers where the Flash memory density ranges between 32 to 128 Kbytes - Medium-Density STM8A devices are the STM8AF622x/4x, STM8AF6266/68, STM8AF612x/4x, and STM8AF6166/68 microcontrollers where the Flash memory density ranges between 8 to 32 Kbytes - High-Density STM8S devices are the STM8S207xx, STM8S007 and STM8S208xx microcontrollers where the Flash memory density ranges between 32 to 128 Kbytes. - Medium-Density STM8S devices are the STM8S105x and STM8S005 microcontrollers where the Flash memory density ranges between 16 to 32-Kbytes. - Low-Density STM8S devices are the STM8S103xx, STM8S003, STM8S001 and STM8S903xx microcontrollers where the Flash density is 8 Kbytes. *

© COPYRIGHT STMicroelectronics

*/

近期下载者：

相关文件：

评论：[我要评论] [举报此文件]

收藏者：