TIM2-output-two-PWM-signal.
所属分类：单片机开发
开发工具：C/C++
文件大小：810KB
下载次数：26
上传日期：2013-04-14 08:43:45
上 传 者：
zhengxiaobin0
说明： STM32 在keil环境下的编程 定时器TIM2能够输出两路PWM信号。
(STM32 Timer programming in keil environment is the TIM2 able to output two PWM signal.)
文件列表:
TIM2两路PWM输出\HARDWARE\EXTI\exti.c (1756, 2011-01-12)
TIM2两路PWM输出\HARDWARE\EXTI\exti.h (628, 2011-01-12)
TIM2两路PWM输出\HARDWARE\KEY\key.c (1795, 2011-01-12)
TIM2两路PWM输出\HARDWARE\KEY\key.h (839, 2011-01-12)
TIM2两路PWM输出\HARDWARE\LED\led.c (942, 2011-01-12)
TIM2两路PWM输出\HARDWARE\LED\led.h (288, 2010-05-27)
TIM2两路PWM输出\HARDWARE\TIMER\timer.c (1475, 2013-04-07)
TIM2两路PWM输出\HARDWARE\TIMER\timer.h (722, 2013-04-07)
TIM2两路PWM输出\HARDWARE\WDG\wdg.c (2088, 2011-01-12)
TIM2两路PWM输出\HARDWARE\WDG\wdg.h (756, 2011-01-12)
TIM2两路PWM输出\keilkilll.bat (399, 2011-04-23)
TIM2两路PWM输出\SYSTEM\delay\delay.c (2038, 2011-01-12)
TIM2两路PWM输出\SYSTEM\delay\delay.h (876, 2011-01-12)
TIM2两路PWM输出\SYSTEM\sys\sys.c (6885, 2011-01-12)
TIM2两路PWM输出\SYSTEM\sys\sys.h (3839, 2011-01-12)
TIM2两路PWM输出\SYSTEM\usart\usart.c (3342, 2011-04-17)
TIM2两路PWM输出\SYSTEM\usart\usart.h (1054, 2011-04-17)
TIM2两路PWM输出\USER\delay.crf (148168, 2013-04-07)
TIM2两路PWM输出\USER\delay.d (1629, 2013-04-07)
TIM2两路PWM输出\USER\delay.o (171196, 2013-04-07)
TIM2两路PWM输出\USER\delay.__i (282, 2013-04-07)
TIM2两路PWM输出\USER\exti.crf (155458, 2012-10-20)
TIM2两路PWM输出\USER\exti.d (1794, 2012-10-20)
TIM2两路PWM输出\USER\exti.o (179812, 2012-10-20)
TIM2两路PWM输出\USER\key.crf (150556, 2012-10-20)
TIM2两路PWM输出\USER\key.d (1625, 2012-10-20)
TIM2两路PWM输出\USER\key.o (174788, 2012-10-20)
TIM2两路PWM输出\USER\led.crf (149769, 2013-04-07)
TIM2两路PWM输出\USER\led.d (1593, 2013-04-07)
TIM2两路PWM输出\USER\led.o (172184, 2013-04-07)
TIM2两路PWM输出\USER\led.__i (292, 2013-04-07)
TIM2两路PWM输出\USER\STM32F10x.d (26, 2013-04-07)
TIM2两路PWM输出\USER\STM32F10x.lst (35306, 2013-04-07)
TIM2两路PWM输出\USER\STM32F10x.o (5680, 2013-04-07)
TIM2两路PWM输出\USER\STM32F10x.s (11307, 2009-12-22)
TIM2两路PWM输出\USER\sys.crf (151742, 2013-04-07)
TIM2两路PWM输出\USER\sys.d (1561, 2013-04-07)
TIM2两路PWM输出\USER\sys.o (176528, 2013-04-07)
TIM2两路PWM输出\USER\sys.__i (272, 2013-04-07)
... ...
本实验将实现如下功能：利用TIM3的通道2（PA7）产生PWM来控制DS0的亮度，实现DS0从 暗->亮->暗的循环变化。
注意:
1,本代码可以JTAG/SWD下载仿真.
2,本代码下载完了之后,需要用跳线帽短接PA7和PA8,否则观测不到结果.
3,实验完毕,请把跳线帽放回原位(不要再短接PA7和PA8),否则可能导致其他实验无法正常运行
正点原子@ALIENTEK
2010-12-29
购买：http://shop62103354.taobao.com
http://shop62057469.taobao.com
技术支持论坛：www.openedv.com
近期下载者：
相关文件：
收藏者：