文件列表:

STR71XGCC\demo.c (4683, 2009-04-16)
STR71XGCC\demo.sh (87, 2009-04-16)
STR71XGCC\freertos\croutine.c (13432, 2009-04-16)
STR71XGCC\freertos\include\croutine.h (27410, 2009-04-16)
STR71XGCC\freertos\include\FreeRTOS.h (4966, 2009-04-16)
STR71XGCC\freertos\include\list.h (11342, 2009-04-16)
STR71XGCC\freertos\include\portable.h (6047, 2009-04-16)
STR71XGCC\freertos\include\projdefs.h (2136, 2009-04-16)
STR71XGCC\freertos\include\queue.h (16893, 2009-04-16)
STR71XGCC\freertos\include\semphr.h (10222, 2009-04-16)
STR71XGCC\freertos\include\task.h (32084, 2009-04-16)
STR71XGCC\freertos\list.c (7686, 2009-04-16)
STR71XGCC\freertos\portable\GCC\ARM7_STR71X\port.c (6831, 2009-04-16)
STR71XGCC\freertos\portable\GCC\ARM7_STR71X\portISR.c (8230, 2009-04-16)
STR71XGCC\freertos\portable\GCC\ARM7_STR71X\portmacro.h (10329, 2009-04-16)
STR71XGCC\freertos\portable\MemMang\heap_1.c (4495, 2009-04-16)
STR71XGCC\freertos\portable\MemMang\heap_2.c (9078, 2009-04-16)
STR71XGCC\freertos\portable\MemMang\heap_3.c (2497, 2009-04-16)
STR71XGCC\freertos\queue.c (31106, 2009-04-16)
STR71XGCC\freertos\tasks.c (61313, 2009-04-16)
STR71XGCC\FreeRTOSConfig.h (3109, 2009-04-16)
STR71XGCC\libstr71x\71x_lib.c (3718, 2009-04-16)
STR71XGCC\libstr71x\adc12.c (3531, 2009-04-16)
STR71XGCC\libstr71x\apb.c (1195, 2009-04-16)
STR71XGCC\libstr71x\bspi.c (6869, 2009-04-16)
STR71XGCC\libstr71x\can.c (21205, 2009-04-16)
STR71XGCC\libstr71x\eic.c (3113, 2009-04-16)
STR71XGCC\libstr71x\emi.c (1195, 2009-04-16)
STR71XGCC\libstr71x\flash.c (13958, 2009-04-16)
STR71XGCC\libstr71x\gpio.c (4199, 2009-04-16)
STR71XGCC\libstr71x\i2c.c (13530, 2009-04-16)
STR71XGCC\libstr71x\include\71x_conf.h (2050, 2009-04-16)
STR71XGCC\libstr71x\include\71x_it.h (2327, 2009-04-16)
STR71XGCC\libstr71x\include\71x_lib.h (2061, 2009-04-16)
STR71XGCC\libstr71x\include\71x_map.h (11649, 2009-04-16)
STR71XGCC\libstr71x\include\71x_type.h (2234, 2009-04-16)
STR71XGCC\libstr71x\include\adc12.h (7921, 2009-04-16)
STR71XGCC\libstr71x\include\apb.h (3523, 2009-04-16)
STR71XGCC\libstr71x\include\bspi.h (15513, 2009-04-16)
STR71XGCC\libstr71x\include\can.h (16306, 2009-04-16)
... ...

FreeModbus STR71X/FreeRTOS/GCC Port REQUIREMENTS ============ This port is the same as the STR71X port but contains complete startup scripts, makefiles and debugger scripts to work without the Rowley Crossworks tools. On the software side a GCC [1] installation (tested with 4.1.1) is required together with a working C-Library [2]. If debugging is desired a Wiggler interface must be present. OpenOCD [3] binaries for Windows and Linux are provided in the tools directory together with a suitable configuration. [1] ... GNU ARM Homepage http://www.gnuarm.org/ [2] ... The Newlib Homepage http://sources.redhat.com/newlib [3] ... OpenOCD homepage http://openocd.berlios.de/web/ USAGE ===== A makefile is supplied with the demo application and a binary can be produced by calling 'make all'. A special target 'debug' is provided which executes the insight debugger. Command line debugging with GDB is also possible and is described here. After you have compiled the binary start the OpenOCD daemon in a shell. $ ./tools/openocd -f tools/str71x_wig.cfg Info: openocd.c:82 main(): Open On-Chip Debugger (2006-08-01 12:00 CEST) Then start the GDB debugger and continue till you have reached the main entry point. $ arm-elf-gdb -se=demo.elf --command=support/target-71.gdb GNU gdb 6.5.0.20060626-cvs ... (gdb) target remote localhost:3333 Remote debugging using localhost:3333 0x00000004 in ?? () (gdb) setup-and-load-ram requesting target halt and executing a soft reset software breakpoints enabled Breakpoint 1 at 0x400011e4: file demo.c, line 53. Mapped internal SRAM at address 0x00000000 (gdb) load demo.elf Loading section .text, size 0x945c lma 0x20000000 Loading section .rodata, size 0x40c lma 0x2000945c Loading section .data, size 0x90 lma 0x2000***68 Start address 0x20000000, load size 39160 Transfer rate: 99170 bits/sec, 495 bytes/write. (gdb) stepi _start () at system/startup.S:97 97 ldr pc, =NextInst Current language: auto; currently asm (gdb) c Continuing. main () at demo.c:53 53 RCCU_Div2Config( ENABLE ); Current language: auto; currently c (gdb) Now you are ready to start or debug the application. If you want to test your system simply enter 'continue' at the prompt. Now start the Modbus test application [1] from the 'demo.sh' or 'demo.bat' shell script. You should see the following output. $ ./demo.sh modpoll - FieldTalk(tm) Modbus(R) Polling Utility ... Protocol opened successfully. Polling slave (Ctrl-C to stop) ... [1000]: 5 [1001]: 0 [1002]: 0 [1003]: 0 If this is working then congratulations. The Modbus Stack and the Target Hardware is ready. [1] ... You need the FieldTalk Modpoll Modbus Polling Tool which you can get at http://www.focus-sw.com/fieldtalk/modpoll.html. FLASH DOWNLOAD ============== Flash download is possible with OpenOCD. First edit the Makefile and set the variable RAM_RUN to ROM_RUN and execute 'make clean' and 'make all'. Open a telnet connection to your OpenOCD daemon and enter the following commands at the telnet prompt: $ telnet localhost 4444 Trying 127.0.0.1... Connected to localhost.localdomain (127.0.0.1). Escape character is '^]'. Open On-Chip Debugger > flash probe 0 flash 'str7x' found at 0x40000000 > flash erase 0 0 9 > flash erase 1 0 3 > flash write 0 demo.bin 0x0 wrote file ../demo.bin to flash bank 0 at offset 0x00000000 in 82s 783us Now restart the target system and the it with the demo application. It is also possible to attach a debugger but you are limited to two hardware breakpoints. Use the same procedure as above but leave out the load step and replace 'setup-and-load-ram' by 'setup-and-load-rom'. COMMON PROBLEMS =============== The following list should serve as a checklist where each point must be satisfied for the port to work. - If you have changed the execution mode make sure you have called 'make clean' $Id: README.txt,v 1.2 2006/11/02 23:29:47 wolti Exp $ STR71X FreeModbus Port Copyright (c) 2006 Christian Walter.

近期下载者：

相关文件：

评论：[我要评论] [举报此文件]

收藏者：