ADI-Blachfin_example
所属分类:嵌入式/单片机/硬件编程
开发工具:C/C++
文件大小:20KB
下载次数:15
上传日期:2008-08-31 15:32:58
上 传 者:
ShawnFeng
说明: 基于ADI blackfin处理器的范例程序
(ADI blackfin processor based on the example of the procedure)
文件列表:
AD9866.dpj (8426, 2004-04-20)
AD9866.dpj.bak (6443, 2004-01-27)
AD9866.mak (14356, 2004-05-03)
AD9866.vdw (27759, 2004-03-24)
adsp-BF533_C.ldf (10633, 2003-12-19)
Init Interrupts.c (2662, 2004-04-29)
Init PPI.c (1173, 2004-04-15)
Init SDRAM.c (522, 2003-03-28)
Init Timer for PPI.c (296, 2004-04-28)
InitFlash.c (1141, 2004-01-27)
main.c (7549, 2004-05-07)
MxFE_SPI_interface.c (2870, 2004-02-10)
process.c (1458, 2004-04-15)
set_PLL.c (1090, 2003-10-23)
Start PPI.c (416, 2003-11-03)
system.h (3046, 2004-04-20)
AD***66 Evaluation Board Rev. A Settings:
Place a 25 MHz oscillator in socket U4. This clocks
the ADC, DAC and Blackfin PPI.
Supply an analog signal to the ADC via the J4 RXIN SMA connector.
The DAC on the AD***66 is designed to handle broadband communications data.
Therefore, when testing the interface, it is best to use analog input
signals with frequency content of 200 kHz and above.
The J5 SMA connector is an analog output from the DAC that can be routed to an
oscilloscope to view the DAC output signal.
The TX port on the AD***66 should be connected to the J3 (HSC interface to ADC) header on the extender card upside-down.
Hence, with the right connection in place, the top of the AD***66 board should face in the same direction as the back of
the extender card.
A short RJ45 cable should be used to connect the SPI ports on the AD***66 board and the extender card.
dip-switches
SW2,4,5,6: ALL OFF
SW3: 1,2 ON, 3,4 OFF
jumpers:
JP54 (solder contact): closed
L3->L12 (power supply jumpers): all closed
JP3, JP7: all closed
JP67,68: close 2<->3
JP 90, 91, 92: close 1<->3
JP77, JP78: close 1<->2
Extender Board Settings:
ADDS-BF561-EZEXT
SW1 (DIR_CONTROL):
1: ON
2-6: OFF
SW2:
1,2: ON
3,4: OFF
SW3:
1-4: ON
SW4:
1-6: OFF
P7, P10, P37: Open
P36: Closed
** If using the now obsolete ADDS-BF533-1-EZEXT **
SW1 (DIR_CONTROL):
1: ON
2-6: OFF
SW2:
1,3,5,6: ON
2,4: OFF
P7: Closed
P10: Open
Note:
Finally, on revision A of the AD***66 board, there is the possibility ofunwanted contention on the DSP_RXEN pin.
If you are using this board revision , you should cut the trace connecting DSP_RXEN on J9 to resistor bank RP13.
Subsequently, you can use a short jumper cable to connect the DSP_RXEN pin to the center pin of JP93.
近期下载者:
相关文件:
收藏者: