说明：DIRECT TORQUE CONTROL OF PERMANENT MAGNET SYNCHRONOUS MOTOR USING THREE-LEVEL INVERTER

说明：SPWM inverter code with schematic

说明：基于DSP2812的单相全桥逆变结构的SPWM程序。。

说明：Cascaded multi-level inverter

说明：here is space vector of five phase inverter

说明：this file is simulink of self inverter in matlab software

说明：在PSCAD/EMTDC软件环境下进行电压源换流器型直流输电系统仿真的文件和代码。

说明：：对全桥型逆变器的滑模控制方案进行了分析，包括建 立系统的变结构模型、选择滑模切换线和确定控制作用，给 出可到达条件及滑模存在区域等。着重讨论了在实际电路设 计中选择开关面系数和开关频率的原则，并且给出相应的设 计程序。

说明：一种500W以下的_绿色三相VF变频器设计

说明：space vector pwm inverter implementation using matlab simulation

说明：pwm inverter simulation using matlab used in power electronics

说明：inverter simulation with lead acid battery communication blocks are used

说明：A three-phase motor rated 1 kW, 500 Vdc, 3000 rpm is fed by a six step voltage inverter. The inverter is a MOSFET bridge of the SimPowerSystems™ library. A speed regulator is used to control the DC bus voltage. The inverter gates signals are produced by decoding the Hall effect signlas of the motor. The three-phase output of the inverter are applied to the PMSM block s stator windings. The load torque applied to the machine s shaft is first set to 0 and steps to its nominal value (11 N.m) at t = 0.1 s. Two control loops are used. The inner loop synchronises the inverter gates signals with the electromotive forces. The outer loop controls the motor s speed by varying the DC bus voltage.

说明：The induction motor is fed by a current-controlled PWM inverter which is built using a Universal Bridge block. The motor drives a mechanical load characterized by inertia J, friction coeficient B, and load torque TL . The speed control loop uses a proportional-integral controller to produce the quadrature-axis current reference iq* which controls the motor torque. The motor flux is controlled by the direct-axis current reference id*. Block DQ-ABC is used to convert id* and iq* into current references ia*, ib*, and ic* for the current regulator. Current and Voltage Measurement blocks provide signals for visualization purpose. Motor current, speed, and torque signals are available at the output of the Asynchronous Machine block.

说明：This circuit uses the AC6 block of SimPowerSystems™ library. It models a permanent magnet (PM) synchronous motor drive with a braking chopper for a 3HP motor. The PM synchronous motor is fed by a PWM voltage source inverter, which is built using a Universal Bridge Block. The speed control loop uses a PI regulator to produce the flux and torque references for the vector control block. The vector control block computes the three reference motor line currents corresponding to the flux and torque references and then feeds the motor with these currents using a three-phase current regulator.

说明：Hysteresis control for solar inverter

说明：atmel-ups-inverter scm

说明：这是一个Matlab实现的三逆变器的Simulink仿真。电流环反馈，pll环控制相位无偏差。

说明：这是一个光伏并网逆变器的仿真，结果良好。希望对学习的人有用

说明：本装置采用单相桥式DC-AC逆变电路结构，以TI公司的浮点数字信号控制器TMS320F28335 DSP为控制电路核心，采用规则采样法和DSP片内ePWM模块功能实现SPWM波。最大功率点跟踪（MPPT）采用了恒压跟踪法（CVT法）来实现，并用软件锁相环进行系统的同频、同相控制，控制灵活简单。采用DSP片内12位A/D对各模拟信号进行采集检测，简化了系统设计和成本。本装置具有良好的数字显示功能，采用CPLD自行设计驱动的4.3’’彩色液晶TFT LCD非常直观地完成了输出信号波形、频谱特性的在线实时显示，以及输入电压、电流、功率，输出电压、电流、功率，效率，频率，相位差，失真度参数的正确显示。本装置具有开机自检、输入电压欠压及输出过流保护，在过流、欠压故障排除后能自动恢复。

说明：非常实用的基于数字信号处理芯片的三相变频器原理图

说明：It is 27 level asymmetrical multilevel inverter

说明：变频技术原理及应用，Bosch培训内容，简单介绍变频器原理和应用，适合初学者

说明：基于DSP的变频器设计，详细介绍变频器设计的原理，比如SPWM，SVPWM等

说明：A NEW TOOLBOX APPLICATION OF MULTI-LEVELS VOLTAGE SOURC INVERTER ADD TO SIMULINK MATLAB

说明：pic16f73做的功率50~4000w逆变器proteus仿真

说明：simulink model of an z source inverter and boost converter. try to verify the performance. it is for study purpose..

说明：simulink model of an impedance source inverter. try to verify the performance. it is for study purpose..

说明：inverter designing is gigen with matlab simulation. It can be very useful for designers...

说明：光伏并网逆变器的仿真，通过仿真可以观察逆变以后的波形，有simulink仿真图