说明：STM32驱动三相电机，包括三电阻、单电阻反馈，foc算法。

说明：induction motor modelling for electrical

说明：直流电机交流电机的驱动芯片和代码L298

说明：单片机驱动三路电机,由stm32单片机的三个端口输出PWM波使电机转动。

说明：异步电动机直接转矩控制书籍 很好的一本书

说明：自己建立的ipark变换模块，根据TI公司永磁电动机例程编写

说明：直线电机simulink模型，希望大家提出意见

说明：在pscad中，双馈，同步，异步，电机频率特性的对比

说明：这设计的是异步电动机的模型和svpwm控制的数学模型的仿真与研究

说明：利用matlab编写的电动机模糊软启动程序，分为s函数和m函数

说明：基于DSP的感应电动机直接转矩控制系统研究,基于DSP的感应电动机直接转矩控制系统研究

说明：ADRC相关文档 simulink 包括eso npd dc motor部分

说明：三相异步电机磁链开关SVPWM系统SIMULINK仿真，通过测试。需要先运行PARA.M配置参数

说明：Stepping motor manual

说明：Motor control reference guide

说明：电机矢量控制模型，控制参数可调，模型可改变成任何电机。

说明：关于电机驱动芯片L298N的仿真及源程序

说明：fuzzy systeme for control of a motor velocity includes the simulink use and the conection to an adquision data card

说明：无刷无感电机调速，带欠压，过流保护，手把信号，无霍尔传感器。

说明：永磁同步电机直接转矩控制仿真，按照博士论文中规中矩建立的直接转矩控制模型

说明：Fuzzy Auto PID Tuning for DC Motor The Fuzzy system needs 2 inputs e(t) & de(t) and it will get three outputs for tuning the PID gains (KP), (KI) & (KD) depending on the membership functions

说明：Stepping motor Stepping motor

说明：变频器软件详细源码 FOC SVPWM- Source Code for dsPIC33EP512MU810 and dsPICDEM MCHV

说明：The induction motor is fed by a current-controlled PWM inverter which is built using a Universal Bridge block. The motor drives a mechanical load characterized by inertia J, friction coeficient B, and load torque TL . The speed control loop uses a proportional-integral controller to produce the quadrature-axis current reference iq* which controls the motor torque. The motor flux is controlled by the direct-axis current reference id*. Block DQ-ABC is used to convert id* and iq* into current references ia*, ib*, and ic* for the current regulator. Current and Voltage Measurement blocks provide signals for visualization purpose. Motor current, speed, and torque signals are available at the output of the Asynchronous Machine block.

说明：This circuit uses the AC6 block of SimPowerSystems™ library. It models a permanent magnet (PM) synchronous motor drive with a braking chopper for a 3HP motor. The PM synchronous motor is fed by a PWM voltage source inverter, which is built using a Universal Bridge Block. The speed control loop uses a PI regulator to produce the flux and torque references for the vector control block. The vector control block computes the three reference motor line currents corresponding to the flux and torque references and then feeds the motor with these currents using a three-phase current regulator.

说明：The system is about simple Vector Control of Permanent Magnet Synchronous Motor. The speed controller is using PI controller and the current controller is using Hysteresis band.

说明：适合初学者的很好的永磁同步电机仿真模型，模型十分清晰

说明： 完整的dspic30f系列控制电机，加上1602和12864的现实。

说明：motor speed control c program

说明：产生占空比变化的脉冲信号。它产生的脉宽调制信号用于电机变速控制。来自马忠梅等编著的《单片机的C语言应用程序设计（第4版）》，北航出版。