eeupdate5.3.rar

  • j5_876660
    了解作者
  • 2.1MB
    文件大小
  • rar
    文件格式
  • 0
    收藏次数
  • VIP专享
    资源类型
  • 0
    下载次数
  • 2022-06-14 18:28
    上传日期
1,用“HP优盘启动盘格式化DOS启动盘工具”格式化U盘,选择FAT32 快速格式化 使用内部DOS系统,完成后就制作完成了纯DOS7.1启动盘。 2,将eeupdate5.3文件夹里面的文件全部复制到U盘根目录下,注意不要把文件夹直接复制到U盘根目录 3,重启电脑,进BIOS设置该DOS启动U盘为第1启动盘或开机按F7选择从该DOSU盘启动 4,这时系统直接进入DOS系统了,输入eeupdate.exe后按Enter键,查看nic下方的数字,我的是1 5,输入命令eeupdate /nic=1 /mac=001132****** 按Enter键,成功修改MAC
eeupdate5.3.rar
  • eeupdate5.3
  • celo.exe
    439.2KB
  • EEUPDMAC.txt
    440B
  • eeupdatew32.exe
    448KB
  • eeupdate.exe
    720.3KB
  • lanconf.exe
    599.1KB
  • old release notes.txt
    16.9KB
  • 使用说明.txt
    454B
  • HP优盘启动盘格式化DOS启动盘工具.EXE
    432KB
内容介绍
Intel(R) EEUpdate Release Notes ================================ April 26, 2005 DISCLAIMER ========== This software is furnished under license and may only be used or copied in accordance with the terms of the license. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Intel Corporation. Intel Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in this document or any software that may be provided in association with this document. Except as permitted by such license, no part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Intel Corporation. Contents ======== - OVERVIEW - RUNNING THE UTILITY - OPTIONS - BASIC USAGE GUIDELINES - EEPROM IMAGE FILE FORMAT - MAC ADDRESS FILE FORMAT - EELOG.DAT - EXAMPLES - ERROR CODES - INSTALLATION - CUSTOMER SUPPORT -LEGAL OVERVIEW ======== EEUpdate is the EEPROM Update Utility. Allows manufacturing programming of EEPROMs, in cases where EEPROM is not preprogrammed, or programmed at In-circuit test. RUNNING THE UTILITY =================== Using the "/?" option will display a list of supported command line options. NOTE: EEPROM checksums and CRCs are automatically updated with any command that modifies the EEPROM contents. In order to prevent these from being updated, use the "/NOCHKSUM" option in the command line. OPTIONS: -------- EEUPDATE can be run with any of the following command line options: /HELP or /? Displays command line help. /EXITCODES Displays exit code help. /ALL Selects all adapters found in the system. /NIC=XX Selects a specific adapter (1-32). /BUS=XX Selects PCI bus of adapter to program. Must be used with the DEV parameter to specify an adapter. /DEV=XX Selects PCI device of the adapter to program. Must be used with the BUS parameter to specify an adapter. /FUN=XX Selects PCI function of the adapter to program. Must be used with both the BUS and DEV parameters to specify an adapter. /DEVICE=<pci device id> 4 hex digit device id of card to program. /DUMP Dumps EEPROM memory contents to file. /CB <offset> <bitmask> Clears bits in the EEPROM, specified in <bitmask>. /SB <offset> <bitmask> Sets bits in the EEPROM, specified in <bitmask>. /RW <word> Reads <word> from the EEPROM. /WW <word> <value> Writes <value> into <word> in EEPROM. /MAC=macaddr Programs the EEPROM with only the MAC address of macaddr without changing the rest of the EEPROM. /A <addrfile rel='nofollow' onclick='return false;'> or /address <addrfile rel='nofollow' onclick='return false;'> Programs the EEPROM with only the MAC address from the <addrfile rel='nofollow' onclick='return false;'> without changing the rest of the EEPROM. /D <imagefile> or /DATA <imagefile> Programs the EEPROM with the contents of <imagefile> without changing the MAC address. /NOCHKSUM Prevents EEPROM checksum and CRCs from being updated. /CALCCHKSUM Forces the EEPROM checksum and CRCs to be updated. /EEPROMVER Displays the version of the EEPROM image. /PCIINFO Displays the PCI information of the adapter. /TEST Checks the EEPROM checksum and size. /IDFLASH Displays the flash ID and its protected status. /DEFAULTCONFIG or /DEFCFG Resets words 30h to 32h back to default. /BOOTDISABLE or /BD Disables Boot ROM. /BOOTENABLE or /BE Enables Boot ROM. /WOLDISABLE or /WOLD Disables WOL bit. /WOLENABLE or /WOLE Enables WOL bit. /SETUPENABLE or /STE Enables Setup Menu. /SETUPDISABLE or /STD Disables Setup Menu. /TITLEENABLE or /TLE Enables Initial Title Message. /TITLEDISABLE or /TLD Disables Initial Title Message. /PROTOCOLENABLE or /PROE Enables Changing the Boot Protocol Option. /PROTOCOLDISABLE or /PROD Disables Changing the Boot Protocol Option. /ORDERENABLE or /ORDE Enables Changing the Boot Order Option. /ORDERDISABLE or /ORDD Disables Changing the Boot Order Option. /LWSENABLE or /LWSE Enables Changing the Legacy OS Wakeup Support Option. /LWSDISABLE or /LWSD Disables Changing the Legacy OS Wakeup Support Option. /SETWAITTIME=X or /SWT=X Changes the setup message delay time (0, 2, 3, 5) on the NIC. /BMCMAC_DUMP Displays the dedicated MAC address for the BMC. /MNGMAC=macaddr Programs the dedicated MAC address for the manageability component without changing the rest of the EEPROM. /MNGADDRESS <addrfile rel='nofollow' onclick='return false;'> Programs the dedicated MAC address for the manageability component with the MAC address from <addrfile rel='nofollow' onclick='return false;'>. /VERSION Displays version and the diagnostic library information. /GUI Brings up GUI mode. /NOPROT On AMT, while programming an image, disables protection. Note this switch has no effect if not used with the /data command. /BMCMAC=macaddr is replaced with MNGMAC command. /BMCADDRESS <addrfile rel='nofollow' onclick='return false;'> is replaced with MNGADDRESS command. /RETAINMNGMAC Uses the manageability MAC address in the NVM rather than the image /DEBUGLOG <debugfile> Log debug messages into the debugfile. /VERIFY <targetfile> Verifies the eeprom image in eeprom to the target file specified in <targetfile>. BASIC USAGE GUIDELINES ---------------------- To display a list of installed adapters call EEUPDATE without any parameters as follows: EEUPDATE EEUPDATE will display a list of network adapters installed in the system similar to the following: [EEUPDATE ver 5.0.1.0] - Intel PCI NIC EEPROM Utility Copyright (C) 1995 - 2004 Intel Corporation Intel (R) Confidential and not for general distribution. Warning: No Adapter Selected NIC Bus Dev Fun Vendor-Device Branding string === === === === ============= ================================================= 1 1 00 00 8086-1008 Intel(R) PRO/1000 XT Server Adapter 2 1 08 00 8086-1039 Intel(R) PRO/100 VE Network Connection To perform an operation on an installed network adapter you must specify the "/NIC=" parameter. For example, to perform an EEPROM dump on NIC 3 from the list above call EEUPDATE like this: EEUPDATE /NIC=3 /DUMP Alternatively you may specify the "/BUS=" and "/DEV=" parameters instead of the "/NIC=" parameter to specify which network adapter to select. For example to program NIC 1 from the list above with the EEPROM image file "image.eep" call EEUPDATE.EXE as follows: EEUPDATE /BUS=0 /DEV=D /DATA image.eep EEPROM IMAGE FILE FORMAT ------------------------ The <imagefile> parameter designates a text file which contains hexadecimal values with which to program the EEPROM. Each value should consist of up to four hex digits seperated by a space or newline. The data contained in <imagefile> must be formatted the same as the EEPROM imagefile produced by the "/dump" parameter. An imagefile produced by the "/dump" parameter may be used to program the EEPROM. Comments may be added to the EEPROM image file as long as they are preceded by a semicolon ';'. NOTE: When programming the EEPROM using the "/DATA" parameter, EEupdate will ignore the MAC Address (first 6 bytes), and EEPROM checksum (last 2 bytes). However, the MAC Address and checksum locations in the EEPROM image file must be filled with valid hexadecimal val
评论
    相关推荐
    • doscmd-开源
      doscmd实用程序模拟PC BIOS的足够大的子集,以引导较早的DOS版本并运行DOS应用程序。
    • BIOS和DOS中断
      在现实生活和工作中,常会有将两台计算机实现资源共享和数据交换的要求。微机双机直接通讯的方法有很多种,根据两台微机的距离远近,可分为近程通讯和远程通讯,如果两台通讯的微机在同一间屋内或相距在几十米到一两...
    • 制作U盘DOS工具
      制作U盘DOS工具,很简单的制作工具,纯DOS系统,用来写BIOS很方便
    • BIOS和DOS中断大全
      BIOS和DOS中断大全 中断INT 21H : 1、字符功能调用类(Character-Oriented Function) 01H、07H和08H —从标准输入设备输入字符 02H —字符输出 03H —辅助设备的输入 04H —辅助设备的输出 05H —打印输出 06H —...
    • BIOS与DOS中断大全
      BIOS与DOS中断大全,提供全面的中断查询
    • iOS-Coding-Style:iOS编码规范
      iOS编码规范 Objective C的代码需要有良好的自解释性,清晰的命名和文档结构,少量的注释。 方法命名 1.1 方法名首字母小写,其他首字母大写 DosomethingWithParam: (不合适,首字母要小写,之后要使用首字母...
    • MHDD DOS v2.9版
      工作环境在DOS下。需要注意的是,不要将MHDD放在需要检测及修复的硬盘上,另外,MHDD也无法在打开了写保护的软盘、硬盘及光盘上正常工作。 运行MHDD后,MHDD首先同样要检测系统中的所有硬盘并给出连接图示。我们...
    • VIOS DOS.rar
      YAMAHA离线软件,可用作编程。
    • U盘启动的DOS系统
      HPUSB制作U盘启动的DOS系统,让U盘成为一个可运行的DOS系统,可用来刷BIOS版本
    • DOS盘制作工具
      刷新程序和BIOS文件,请自行下载并解压到光盘中即可.此文件为光盘ISO镜像文件,请使用WINIMG将下载的BIOS文件和刷新程序添加到ISO文件中.并重新刻制启动光盘.也可直接将下载的ISO镜象文件使用记录软件制作成光盘,将...